How to Install a Lace Wig with Glue or Tape - Canada Wig Shop
Lace Wig Application With Glue
Always clean the area around the hairline before application. Rubbing alcohol is a good prep to remove excess oil from the area the lace is to be applied on.
- Using a Q-Tip or applicator brush, apply a thin coat of glue around the perimeter of your hairline. Use a blow dryer on low to dry the glue until is not completely dry but tacky. Do NOT bond lace wig to wet glue, the wig will not set properly and will not stick well. The area should be sticky to the touch.
- After your glue is ready for application, you must position the lace wig on your head. To make sure it is aligned properly, you must first bond the wig at the center of your front hairline. (The center point can be determined by parting the hair down the middle and aligning it with the center of your forehead or widows peak.) Then going from one side to the other, press the edge of the wig down into the adhesive using a fine tooth comb.
- Double check your hairline and touch-up any areas where the wig is not applied securely. If you need to remove any excess glue use glue remover.
- When you have completed the application process, tie down your hairline with a silk or satin scarf. This will allow the glue to set and dry properly. You may also sit under a dryer during this step to aide in the drying process.
*IMPORTANT* For those who want to use a tape and glue combination, the glue should go on your
Tools for Applying Your Lace Wig
- Tape or Glue
- Scissors
- Scarf or Cloth or Satin Headband
- Q-Tip or Application Brush
- Bobby Pins or Clips
- Rubbing Alcohol or Scalp Prep
- Blow Dryer
Lace Wig Application With Glue
Always clean the area around the hairline before application. Rubbing alcohol is a good prep to remove excess oil from the area the lace is to be applied on.
- Using a Q-Tip or applicator brush, apply a thin coat of glue around the perimeter of your hairline. Use a blow dryer on low to dry the glue until is not completely dry but tacky. Do NOT bond lace wig to wet glue, the wig will not set properly and will not stick well. The area should be sticky to the touch.
- After your glue is ready for application, you must position the lace wig on your head. To make sure it is aligned properly, you must first bond the wig at the center of your front hairline. (The center point can be determined by parting the hair down the middle and aligning it with the center of your forehead or widows peak.) Then going from one side to the other, press the edge of the wig down into the adhesive using a fine tooth comb.
- Double check your hairline and touch-up any areas where the wig is not applied securely. If you need to remove any excess glue use glue remover.
- When you have completed the application process, tie down your hairline with a silk or satin scarf. This will allow the glue to set and dry properly. You may also sit under a dryer during this step to aide in the drying process.
*IMPORTANT* For those who want to use a tape and glue combination, the glue should go on your skin and the tape should go on the lace. This will actually protect the lace from the wear and tear of the liquid adhesives.
Lace Wig Application With Tape
- Cut the tape into desired shapes, you want the tape to contour your hairline.
- Peel the paper from one side of the double-sided tape and apply the strips of tape around the perimeter of the lace wig. Press firmly into place. *IMPORTANT* You should leave small spaces between the tape to allow for water to escape, if you will be wearing this for extended periods of time.
- Position the lace wig on head, and starting with the center, go from side to side, pressing the wig down in sections with a fine tooth comb. Press firmly, for 30 seconds.
- When you have completed the application process, tie down your hairline with a silk or satin scarf. This will allow the glue to set and dry properly. You may also sit under a dryer during this step to aide in the drying process.
skin and the tape should go on the lace. This will actually protect the lace from the wear and tear of the liquid adhesives.
Lace Wig Application With Tape
- Cut the tape into desired shapes, you want the tape to contour your hairline.
- Peel the paper from one side of the double-sided tape and apply the strips of tape around the perimeter of the lace wig. Press firmly into place. *IMPORTANT* You should leave small spaces between the tape to allow for water to escape, if you will be wearing this for extended periods of time.
- Position the lace wig on head, and starting with the center, go from side to side, pressing the wig down in sections with a fine tooth comb. Press firmly, for 30 seconds.
- When you have completed the application process, tie down your hairline with a silk or satin scarf. This will allow the glue to set and dry properly. You may also sit under a dryer during this step to aide in the drying process.
Click below to view and purchase supplies now.
Watch videos of lace wig application
Check out our human hair lace wigs and buy one today!
DISCLAIMER - PLEASE NOTE - The videos shown in this article are for entertainment and informational purposes only and we do not endorse or recommend that you follow the tips provided.